Value Descriptions
BV100, BIDET DIVERTER VALVE
A DIVERTING VALVE WITH AN INTEGRAL ATMOSPHERIC VACUUM BREAKER.
MADE FROM ENGINEERED CARBON PLASTIC MATERIAL, CORROSION-RESISTANT.
MINIMUM CONTINUE FLOW ON THE SPRAY WHEN ON RIM MODE.
MINIMUM CONTINUED FLOW ON THE RIM WHEN IN THE SPRAY MODE.
THE HOT WATER OF THE BIDET WILL WARM THE BIDET COLD RIM.
THE CONTINUOUS WATER FLOW FROM THE RIM MAINTAINS THE BOWL CLEAN.
TO PROTECT THE BATHER FROM GETTING BURNED BY HOT WATER OR SHOCKED BY COLD WATER.
FROM A SUDDEN CHANGE IN THE PRESET WATER TEMPERATURE.
AN ANTI-SCALD VALVE, SUCH AS A THERMOSTATIC OR A PRESSURE BALANCE VALVE, IS HIGHLY RECOMMENDED.
FOR AN EASY AND TIME-SAVING INSTALLATION, OMNIBRASS IS PLEASED TO MAKE AVAILABLE THE FOLLOWING CUSTOM-MADE FITTINGS,
ONE 3/8 ELBOW, ONE 3/8 “Y”, TWO HOSES 1/5”X 3/8X 12” AND ONE 3/8” X 3/8” X 24” SPRAY HOSE.
THE 3/8" HOSE FITTINGS ARE CUSTOM-MADE, AND THE NUT CAN BE HAND TIGHTEN.
A BIDET WITHOUT A VERTICAL SPRAY AND RIM, WITH ONLY A SINGLE FAUCET, MAY NOT BE SANITARY.
TO CLEAN OR REFRESH, THE BATHER MUST USE THE HANDS AND DUNCK THEM IN THE SAME DIRTY WATER.
THE SPLINE IS A 20-TOOTH; HOWEVER, CUSTOMERS CAN CUSTOM ORDER.
SPLINE, INLET AND OUTLET IS BRASS.
FOR A PLEASANT BIDET EXPERIENCE, THE SPRAY HAS AN AERATOR TO SOFTEN THE SOLID WATER JET.
MAXIMUM OPERATING TEMPERATURE.160 F – [71C.] PRESSURE 125ps – [86 Kpa.].
THE VALVE IS CERTIFIED TO C.S.A. B125 AND A.S.S.E. STANDARDS.
IF ONLY 2 PORTS ARE USED, THEN CAP THE ONE NOT USED.
BV631-SHOWER DIVERTER
A BRASS VALVE BODY WITH FOUR ½" PORTS.
PORTS: THE INSIDE IS FOR ½" SOLDERING COPPER PIPE.
ORTS: THE OUTSIDE IS N.P.T. THREADED.
CARTRIDGE IS AN ENGINEERED CARBON PLASTIC MATERIAL.
THE VALVE HAS TWO SPECIAL STAINLESS STILL STOP WASHERS.
ONE WASHER CONTROLS TWO PORTS, THE LEFT OR RIGHT HAND.
ONE WASHER CONTROLS THREE PORTS.
SMOOTH SWITCHOVER FROM PORT TO PORT.
SPLINE: STANDARD IS A 20-TOOTH. HOWEVER, CUSTOMERS CAN CUSTOM ORDER.
SPLINE: CAN BE REPLACED AT ANY TIME WITHOUT DAMAGING EXISTING FINISHED ARE.
SPLINE: TRIM EXTENSION IS NEVER REQUIRED.
NOTE: IF ONLY 2 PORTS ARE USED, THEN CAP THE ONE NOT USED.
BV635-SHOWER DIVERTER
A BRASS BODY VALVE WITH FOUR ½" PORTS.
PORTS: THE INSIDE RIMMED FOR ½" COPPER PIPE SOLDERED.
PORTS: THE OUTSIDE IS N.P.T. THREADED.
CARTRIDGE: A CERAMIC DISC.
THE VALVE HANDLE TURNED 360 DEGREES LEFT OR RIGHT.
SMOOTH SWITCHOVER FROM PORT TO PORT.
SPLINE: STANDARD IS A 20-TOOTH. HOWEVER, CUSTOMERS CAN CUSTOM ORDER.
SPLINE: CAN BE REPLACED AT ANY TIME WITHOUT DAMAGING EXISTING FINISHED ARE.
SPLINE: TRIM EXTENSION IS NEVER REQUIRED.
NOTE: IF ONLY 2 PORTS ARE USED, THEN CAP THE ONE NOT USED.
BV202-A VACUUM BREAKER
RIM-MOUNT ½" VACUUM BREAKER.
BRASS BODY, CORROSION RESISTANCE COMPONENTS.
COMPONENTS ARE EASILY ACCESSIBLE FROM ABOVE THE DECK.
CONNECTION, FOR ½" COPPER PIPE.
AVAILABLE IN CROME FINISHES.
IDEAL TO BE USED CLEANING AND DISINFECTING WHIRLPOOLS.
COMPLY WITH C.S.A. AND ASSE STANDARD.
BV1000-SIENA SHOWER COLUMN
THE SIENA SHOWER COLUMNS HAVE A NEW INNOVATIVE ELEGANT LOOK.
THE COLUMN IS 33" LONG, 1" DIAMETER AND STRAIGHTER.
TO MAINTAIN A STRAIGHT PRESENCE, THE BEND IS ON TOP OF THE COLUMN.
THE DIVERTER VALVE IS AT THE BOTTOM OF THE COLUMN, THUS CLOSER TO THE FLOOR.
COMFORTABLE FOR THE ENTIRE FAMILY TO OPERATE, CHILDREN INCLUDED.
WHEN THE STRAIT COLUMN IS INSTALLED, IT WILL LOOK ELEGANT.
THE COLUMN, PREVENTS THE HAND-SHOWER HOSE DENGLIN IN FRONT OF THE EXISTING TUB-SHOWER VALVE.
THE SIENA COLUMN, CAN BE INSTALLED EITHER LEFT OR RIGHT END.
THE SHOWER HAD AVE SOFT TIPS FOR EAST CLEANING.
THE HAND SHOWER HOSE IS 60" LONG.
THE HAND SHOWER WAND HAS MULTIPLE FUNCTIONS.
THE SIENA COLUMN, COMPLIES WITH BUILDING STANDARD.
